我司是ABB控制器中国地区唯一授权经销商

ABB 控制器 NextMove e100的详细描述：

轴数：在单个或多个坐标组中的16个插补轴，管理数十个独立的DS402定位驱动器（非插补）。

轴的类型：以太网Powerlink协议（EPL）v2，3个闭环轴±10V带有5VTTL渐进编码器输入接口，4个开环轴-步进电机接口（分布且定向输出）5V差分直线驱动器（5MHz）或由命令选项选出的5V开集电极单端（最大为500KHz）

Powerlink装置，以太网

单板存储器 固件为4M字节闪存和永久程序存储器为10M字节SRAM，永久变量数据存储器为32k字节FRAM

数字输入 20个光电分离的24VDC，采样率为1ms。所有的输入具有中断能力。可与正负公用块连接，可用于范围、位置、停机和驱动误差配置的软件

数字输出 12个光电分离的12-24VDC PNP 用于启动驱动器的可配置软件 每信道标准为50mA 单信道最大负载为350mA 8个信道合计500mA

模拟输出 对于驱动命令信号，有三种输出功率 ±10V、12位分辨率 一通用±10V12位输出

模拟输入 两种误差不超过V±10V，12位分辨率下运行

继电器输出 单输出适用于驱动器启用，额定值为24V（150mA）的C型继电器（单刀双郑），一般为常开常闭状态

串行口 RS485/232

Can总线端口 标准的9针Sub-D型连接器的单CAN端口等

The NextMove e100 builds on the proven NextMove controller family of products, integrating the management of real-time Ethernet using the industry standard protocol Ethernet POWERLINK. Drives, I/O devices, sensors, absolute encoders can all be added to the POWERLINK network and controlled from the MINT programming language. This greatly simplifies system design and installation, and simultaneously expands the capabilities of the NextMove e100 as a machine control platform.

NextMove e100 can perform interpolation for up to 16 axes, either as a single coordinate group or as an independent sub-group in a multitiple coordinate system with interpolation over the Ethernet POWERLINK network or the built in stepper/servo axes. NextMove e100 is compatible with ABB's Ethernet POWERLINK AC servo drives - MicroFlex e100 and MotiFlex e100.

NextMove e100 is part of the e100 motion family including MotiFlex e100, Mint Machine Modules and range of single phase servo drives, MicroFlex e100 all controlled via Ethernet POWERLINK.

NextMove e100 provides control of up to 16 coordinated axes of motion and many more non-coordinated axes. Axes can be split amongst the three phase MotiFlex e100 drives and single phase MicroFlex e100 drives to suit the application requirements.

Compatible with MintNC and HPGL

Ordering information and accessories:

 

NXE100-1608DBW	NextMove e100 8 axis motion controller. Differential stepper outputs
NXE100-1608SBW	NextMove e100 8 axis motion controller. Single ended open collector stepper outputs for use with DSM integrated stepper/driver motors
NXE100-1612DBW	NextMove e100 12 axis motion controller. Differential stepper outputs
NXE100-1612SBW	NextMove e100 12 axis motion controller. Single ended open collector stepper outputs for use with DSM integrated stepper/driver motors
NXE100-1616DBW	NextMove e100 16 axis motion controller. Differential stepper outputs
NXE100-1616SBW	NextMove e100 16 axis motion controller. Single ended open collector stepper outputs for use with DSM integrated stepper/driver motors
OPT036-501	Ethernet POWERLINK Router for remote connection / access to to a POWERLINK system / network
CBL001-501	2m (6ft) RS232 cable for programming and diagnostics (note: 2m (6ft) USB cable included with the motion controller)
CBL034-501	RS232 programming cable (PC to HMI)
MNC001-501	MintNC - Windows profiling front end for NextMove which accepts industry standard files: HPGL, DXF and G-code.
HMI - see ABB operator panels
24V power supplies - see ABB power supplies
Ethernet cables - For connecting NextMove e100 to MicroFlex e100
CBL002CM-EXS	Ethernet Cable: Shielded CAT5e RJ45 200mm / 8in
CBL005CM-EXS	Ethernet Cable: Shielded CAT5e RJ45 500mm / 1.6ft
CBL010CM-EXS	Ethernet Cable: Shielded CAT5e RJ45 1m / 3.2ft
CBL020CM-EXS	Ethernet Cable: Shielded CAT5e RJ45 2m / 6.5ft
CBL050CM-EXS	Ethernet Cable: Shielded CAT5e RJ45 5m / 16.3ft
CBL100CM-EXS	Ethernet Cable: Shielded CAT5e RJ45 10m / 32.6ft